In order to construct optical access networks economically for fiber to the home (FTTH), it is important to reduce the cost of optical fiber cable installation. Optical fiber and cable costs have been reduced over the past ten years, however there have been few reports describing installation cost reduction. In this paper, we describe the design of high-density optical fiber cable that reduces the required installation time. To achieve this we have reduced the optical fiber cable weight and the friction coefficient of the cable sheath. We reduced the cable weight by using polyethylene foam and a non-metallic tensile strength member made of a new material, PBO. These two approaches reduce the cable weight by a total of about 30%. We also added a lubricant to the polyethylene sheath of this cable and this reduced the pulling force required for the additional cable by 30%-50%.

Low cost optical subscriber systems and effective operation are indispensable to the construction and maintenance of greatly expanded optical fiber networks. An optical fiber line monitoring system is essential for reducing maintenance costs and improving service reliability in optical access networks. To promote cost-effective optical fiber line operation, we propose an extended automatic optical fiber operations support system (AURORA) with a remotely installed fiber selector. We suggest a configuration for extended AURORA and design the dynamic range of the system. We confirmed that testing could be carried out on an extended optical network section of 10 km in length by using extended AURORA when the optical trunk line was less than 15 km. We also discuss the effect on the maintenance cost of optical fiber cables in access networks. We calculated the annual maintenance cost for periodic tests in actual operation areas, and confirmed that this cost could be reduced by 30% compared with that for a conventional system.

This paper proposes the technology of wide passband wavelength-division multiplexing (WWDM) for access networks offering multiplexed services. The technology greatly relaxes the wavelength setting accuracy requirements of the WDM light source and the multiplexer/demultiplexer (MUX/DEMUX) compared to dense WDM (DWDM) technology. A WWDM optical converter that offers the Internet protocol (IP) service is implemented and its performance assessed at temperatures ranging from 0C to 45C. In addition, we assess three channel transmission (cable television (CATV) and IP services) in the 1.5 µm region as a multiplexed service example. Using the proposed WWDM, we confirm the feasibility of a service multiplexing system that offers simultaneous CATV and IP services in access networks. This WWDM technology is expected to provide cost effective service multiplexing systems for access networks.

The evolution of access networks towards Fiber-To-The-Home (FTTH) receives much attention throughout the world because FTTH has a big potential for providing future attractive services. To provide such services in terms of transmission rate, the cable network transition scenario from conventional copper cable network to optical fiber cable one in access field should be clarified. Since network transition scenario deeply depends on the service evolution scenarios (what type of service would appear at a certain time and how many customers move to the other services, for example), this paper firstly categorizes telecommunication services into four kinds of services, i.e. Basic Service (e.g. POTS), Narrowband Symmetrical Service (e.g. NISDN), Broadband Asymmetrical Services (e.g. Video-On-Demand) and Broadband Symmetrical Services (e.g. BISDN) in terms of up-and down-stream transmission rates. Based on this service categorization, it is proposed to formalize service evolution scenarios by a transition pattern of the initial demands and the penetration rates of these services. Then, the evaluation method of network transition scenarios is also proposed in terms of NPV by the service evolution scenarios. It is conclude that the network transition scenarios are deeply related to the amount and behavior of the demands moving to the other services as follows.-The scenario where the new system configuration partly replaces the old one whenever the demands appear for providing higher transmission rate services is applicable, when the demands move little or constantly move to the higher transmission rate services,-The scenario where the new system configuration totally replaces the old one at the early stage for providing all services is applicable, when the demands drastically move to the higher transmission rate services during short period.

A hybrid network architecture using subcarrier multiplexed optical fiber (SCMOL) and coaxial cable is proposed in this paper for the access link of future personal communication systems (PCS) between tiny passive radio base stations in microcells and remote central base stations. Results indicate that the required number of laser diodes, photodetectors and amount of fiber could be reduced by more than 4 times with the proposed hybrid access link compared to the point-to-point SCMOL link and the network cost would decrease proportionally.

For the successful realization of the multimedia information environment, it is strongly required to develop very cost effective optical access networks. Accordingly, ways of reducing system cost are described. At the same time, the development of attractive new services is indispensable to drive network modernization. The connectionless networking service for community user groups is proposed together with the new concept of group communication.

Precise direct mounting of laser diode (LD) and photodiode (PD) chips on silica planar lightwave circuits (PLCs) has been investigated for application to transceiver modules. To achieve submicron optical alignment, self-aligned index marks on the PLCs and LDs were directly detected by transmission infrared light. The repeatability of the positioning was measured to be within 0.125 µm. The output power of the resultant module was 0.2 mW at 80 mA. A waveguide-type PD was also mounted in the same way, and module sensitivity of 0.25 A/W was demonstrated.

Currently there is considerable world-wide speculation regarding the introduction of optical fiber cable into access networks, because optical fiber has a big potential for providing attractive multimedia services. Since optical fiber cable can provide a variety of grade of services, high-reliability of cable networks would be required compared with the conventional copper cable networks. To develop multimedia telecommunication networks as an infrastructure, it is urgent to clarify the highly reliable optical fiber cable network architecture. Since cable network architecture deeply depends on regional conditions such as demand, area size, duct layer networks (consisting of ducts, manholes, tunnels, feeder points etc.), it is necessary to develop a cable network designing tool with user-friendly interfaces for efficiently evaluating cable network architectures. This paper firstly proposes the heuristic algorithms enhanced by the disjoint-shortest-path and the depth-first-search methods that would be applicable for real access networks. Secondly, the design method of highly reliable optical fiber cable network based on the heuristic algorithms in terms of network cost and unavailability caused by cable breakdown is proposed. It can design the combination of star- and loop-shaped (where two diversified routes exist between a feeder point and central office) cable network. Furthermore, comparison with the conventional design method which simply applies star- or loop-shaped cable network is done in terms of economy and reliability on real access networks in the Tokyo metropolitan area. It is concluded that the proposed method can reduce the network cost further and realize a short unavailability value compared with the conventional method.